![]() I tried making it one time with medium grade bud, I didnt chop it. good enough to chop and roll joints with, I have 2 of these 250g bags: roll joints with it and you barely know its not bud.Ģ50 grams of nice og kush bottoms. I powderize itin the coffee grinder and it looks amazing. I can get over 6 grams from an oz but my stuff is very "crystally". ![]() I usually run 14-20g runs in my small tube with 3 cans and get 3 grams return of very golden oil. I have been doing it for about 4 years but probably 2 years of those have been wrong and this last year ive really been perfecting it now that I have my own place and am not sneaking everything around. I havent made any that looks like that yet. I absolutely loveeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeee the bho process, and im always trying to figure out new ways of a more thorough purge. things could be quite different, im just too afraid to invest in a tube of that stature, and have a bad outcome. but thats a lotttttttttttt of work!! i dont like to work any more than that at once.īut with a tube that holds a half p or so. in about 2 hours, i can spray a pounds worth. from start to finish, i can pack a fresh tube, spray it, and empty it all in about 15 minutes. so im constantly rotating the drip of thh tane down the tube, to hopefully hit all the goods, and carry them out. I hold the tube at about 20 degrees angle, holding the bottom of the tube just above my dish, i keep the bottom in about the same area, but the top of the tube is where i draw a star pattern as i spray (some people go in a circular motion, i like that star power!), so i start off at one point, and spray for about 15 secs, then hit the next point of the star, 15 secs, then to next point, and so forth. I dont over stuff my tube, but evenly pack it the whole way through. shits sticky andd messyyy, and if your a busy person, your hands probably aint too clean, so where those doctors/tatooers latex gloves. once its all bubbly and stable, continue onward! I would recommend blowing outside, its best to use a nice sunnny day to blow, let mother nature do its natural evap on the stuff till it dont slide around any more, once it hits that stage, bring it into a nice dry climate where it can finish settling at room temp. and the butane cans (power 5)įortunately, i have not had any bad incidents, but i have heard of some ridiculous situations where people just lacked common sense and hurt themselves and or others. the ONLY METAL pieces in my setup are my flat head screw driver, and my hose clamp at the end of the tube. i like to not have any potential metal to metal contact. i use an 8x8 glass pyrex dish, tiny right!!? believe it or not, its plenty of room for at least a few zips extraction. i can firmly pack about 2 zips (60 gs in there) so! for a tube of your dreams, i would say go with a GLASS tube about 50-60 inches long, and keep the diameter around 2.5 inches, i wouldnt go any thicker, but you could always go thinner, but if you go thinner, then you will need to go longer than 50-60 inches. ![]() My tube is 18 inches long, and about 2.5 inches wide. i kind of have a theory that the smaller tube you use, the better quality and yield you get. ![]() SO< about your tube, dude, thats a lottt of blowing, could be efficient though. ALSO! pick out any and ALLL stems you can, stems take up sooo much space in the tube. usually the trim i get comes already ready. i dont use full nugs though, the biggsst nugs i use are littles, less than a bowls worth. he made me a tube that holds about 2 zips, i dont crush my weed, or grind it, i like to treat my product with a lottt of respect. i dont even touch shit that gives me less than 2g an oz. but the quality you put in really effects the outcome. YO!! so how long have you been doing this? what kind of yields are you getting per oz? if i wanted a 50 g brick, with my setup, i would need about a p or so good of trim.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |